Keyless entry

Product Overview

This upgrade adds the complete OE passive entry infrastructure to a vehicle that left the factory without the Keyless Entry option. Our technicians replace the standard front door handles with genuine capacitive‑sensing handles, mount the Keyless Vehicle Module in its designated location, and install interior and exterior LF antennas to create the required detection zones. Once we complete the CCF programming and security calibration, your vehicle recognises the authorised key fob as you approach, unlocks automatically when you touch the handle, and starts with a simple press of the engine button. Additionally, the system enables walk‑away locking and tailgate proximity release on compatible models, all entirely integrated into the vehicle’s existing security architecture.

JLR Keyless Entry Technical Specification

We replicate the exact factory topology for passive entry down to the antenna polling logic and KVM module address. The system behaves identically to a line‑fitted installation, communicating over the CAN and LIN networks with full arbitration of lock/unlock commands, immobiliser release and status feedback to the instrument cluster.

Genuine JLR Capacitive Door Handles

We fit authentic capacitive‑touch exterior handles that contain embedded low‑frequency antennas and sensor electronics. Touching the inner surface of the handle triggers an unlocking request; pressing the small lock button on the handle cap locks all doors. The handle communicates its state to the KVM via a dedicated LIN‑bus line, operating in tandem with the central locking system. Because we use only genuine components, the tactile feel, actuation force and response time precisely match those of a factory‑equipped vehicle.

Antenna Network and Can‑bus Integration

A network of three to five LF antennas — positioned in the centre console, rear luggage area and within each front door — creates consistent detection zones around the vehicle. The KVM broadcasts a 125 kHz wake‑up challenge and measures the fob’s response strength to determine its exact location. This spatial awareness prevents the vehicle from unlocking when the key fob sits only a few centimetres outside the perimeter, a critical security layer. The KVM exchanges data with the Central Gateway Module over the high‑speed CAN bus, coordinating with the immobiliser, Body Control Module and start button to authorise engine cranking seamlessly.

Seamless Operation and Remote Functionality

The system preserves every original remote fob button function while adding passive entry. You can still use the lock, unlock and tailgate buttons, but you no longer need them. Approach the vehicle, and the puddle lamps illuminate; touch the handle, and the doors unlock with the anti‑theft alarm disarmed. Starting the engine requires only the brake pedal and start button. Walk away from the vehicle, and the locks engage automatically after a configurable timeout. The touchscreen menu inside Pivi Pro or InControl Touch Pro also introduces a new “Passive Entry” toggle, allowing you to enable or disable the feature according to your preference.

Software Programming and Vehicle Compatibility

We use official JLR diagnostic equipment to modify the Central Car Configuration file, adding the Keyless Entry feature code and activating the corresponding ECU variants. The KVM then learns the immobiliser encryption and pairs securely with the vehicle’s existing key fobs. We also update the Body Control Module and Instrument Cluster software so the system status appears correctly in the driver display. This full programming ensures your vehicle’s digital service record logs the feature as a genuine equipment item and remains fully compatible with future dealer software updates.

This retrofit suits a broad range of Land Rover and Jaguar models, including Range Rover Evoque L551, Discovery Sport L550, Range Rover Velar L560, Land Rover Defender L663, Jaguar F‑Pace X761, Jaguar XF X260 and Jaguar XE X760. Our team completes a VIN‑based compatibility check before scheduling the installation.

Expert Installation by JLR Specialists

Our technicians install the complete Keyless Entry system in a single working day, following factory workshop procedures.

1. Vehicle Scan and Preparation: We record all module software versions and verify the electrical integrity of the CAN networks.
2. Door Handle Replacement: We replace the front exterior handles with capacitive units, routing the new harness through the door loom conduits to the LIN termination point.
3. Antenna Mounting: We secure the LF antennas in their factory mounting locations — under the centre console, inside the rear bumper cover and within the door cavities — ensuring optimal signal coverage.
4. KVM Installation: We fit the Keyless Vehicle Module onto its bracket behind the dashboard and connect it to the high‑speed CAN, power and ground.
5. Software Configuration: We install the KVM calibration, modify the CCF, enable the Passive Entry menu, and carry out a security immobiliser pairing.
6. Final Testing and Handover: We validate key fob detection at multiple positions around the vehicle, demonstrate the automatic locking sequence, and confirm full integration with the start button and existing alarm system.

Your Effortless Access Experience

Keyless Entry transforms your daily interaction with the vehicle. Walk up with the key in your pocket, and the car welcomes you. Touch the handle, and the doors unlock instantly — no fumbling for the remote in the rain or when carrying shopping. The subtle illumination of the door handle LEDs and interior roof lamp creates a sense of occasion every time you step in. Because the system uses the vehicle’s own certified security electronics, it meets the same theft‑resistance standards as a factory build, with rolling‑code encryption and anti‑relay logic that blocks signal amplification attacks. Your vehicle gains not only convenience but also genuine, fully integrated security.

This retrofit also adds lasting value. The system appears in the vehicle’s build record as an authenticated feature, and any future diagnostic session will detect a coherent, OE‑quality installation. From the precise feel of the capacitive handle to the instant response of the central locking, every aspect mirrors the experience of a top‑tier JLR model.

Add Genuine Keyless Entry to Your Vehicle

Experience the freedom of passive entry with our OEM Keyless Entry retrofit for Land Rover and Jaguar. We provide nationwide mobile installation across the UK, completing the full conversion in one day.

Contact us today for a complimentary VIN‑based compatibility check and a fixed‑price quotation. Every installation includes a 12‑month workmanship warranty and complete handover. Discover the convenience of a vehicle that recognises you automatically and unlocks at your touch.